MIC2583R-KYQS

Microchip Technology
998-MIC2583R-KYQS
MIC2583R-KYQS

Nsx:

Mô tả:
Hot Swap Voltage Controllers Single-Channel Hot-Swap Controller - 150mV Fast-Trip Threshold

Mô hình ECAD:
Tải xuống Thư viện Tải miễn phí để chuyển đổi tệp tin này cho Công cụ ECAD của bạn. Tìm hiểu thêm về Mô hình ECAD.

Sẵn có

Tồn kho:
Không Lưu kho
Thời gian sản xuất của nhà máy:
10 Tuần Thời gian sản xuất tại nhà máy dự kiến.
Tối thiểu: 98   Nhiều: 98
Đơn giá:
$-.--
Thành tiền:
$-.--
Dự kiến Thuế quan:
Sản phẩm này được Vận chuyển MIỄN PHÍ

Giá (USD)

Số lượng Đơn giá
Thành tiền
$3.31 $324.38

Đặc tính Sản phẩm Thuộc tính giá trị Chọn thuộc tính
Microchip
Danh mục Sản phẩm: Bộ điều khiển điện áp hoán đổi nóng
RoHS:  
Controllers & Switches
Programmable
13.2 V
2.3 V
1 Channel
1.5 mA
- 40 C
+ 85 C
SMD/SMT
QSOP-16
Tube
Yes
Nhãn hiệu: Microchip Technology
Quốc gia Hội nghị: Not Available
Quốc gia phân phối: Not Available
Quốc gia xuất xứ: MY
Nhạy với độ ẩm: Yes
Loại sản phẩm: Hot Swap Voltage Controllers
Sê-ri: MIC2583
Số lượng Kiện Gốc: 98
Danh mục phụ: PMIC - Power Management ICs
Đơn vị Khối lượng: 288 mg
Đã tìm thấy các sản phẩm:
Để hiển thị sản phẩm tương tự, hãy chọn ít nhất một ô
Chọn ít nhất một hộp kiểm ở trên để hiển thị các sản phẩm tương tự trong danh mục này.
Các thuộc tính đã chọn: 0

Chức năng này cần phải bật JavaScript.

CNHTS:
8542319090
CAHTS:
8542390000
USHTS:
8542390090
JPHTS:
854239099
TARIC:
8542399000
MXHTS:
8542399901
ECCN:
EAR99

LM5060 High-Side Protection Controllers

Texas Instruments LM5060 High-Side Protection Controllers with Low Quiescent Current offers intelligent control of a high-side N-channel MOSFET during normal on/off transitions and fault conditions. The constant rise time of the output voltage results from the inrush current control. Both an Input UVLO (with hysteresis) and a programmable input OVP are provided, with an enable input offering a remote on or off control. The initial start-up VGS fault detection delay time, the transition VDS fault detection delay time, and the continuous over-current VDS fault detection delay time is programmed from a single capacitor. The MOSFET is latched off until either the enable input, or the UVLO input is toggled low and then high when a detected fault condition persists longer than the allowed fault delay time.